A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
We've noticed the article about How to Install a Bathtub Yourself down the page on the web and believe it made sense to discuss it with you on this page.
Installing a bathtub isn't specifically rocket science, yet it does need solid plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably hard task. If the old tub is easily accessible, the project can move speedily; if you need to open up a wall surface to get rid of the old bathtub and place the brand-new tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub and embeded in the brand-new one. Make sure you have qualified on your own for the work as well as fit attempting it. Rather than working with a professional to take control of a halfway-completed job, it is far better to think about using one before you begin. Possibilities are you might require a professional plumber to make tube links.
This article will certainly help you install a new bathtub in your bathroom if you have actually currently purchased a new bathtub and also don't require to alter the arrangement of your previous water pipelines.
Your tools as well as product checklist ought to consist of the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of removing the existing taps can be fairly troublesome due to the limited access that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old taps to the new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washing machines are in area in between the faucet and also the sink. Protect the faucet in place with the producer supplied backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The former kind must be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using both wooden boards under its feet, position the bathtub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the bathtub until the level reads degree.
To install taps, fit all-time low of the outermost flexible faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Turn on the water system as well as check all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub and additionally check the overflow electrical outlet and the typical outlet for leaks.
Ultimately, take care of the bath paneling as described in the producer's instruction manual. Tiling and securing around the tub should wait up until the bath tub has been used at least once as this will certainly settle it right into its final position.
Getting ready for the Installment
First of all, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets device to prevent strain on the bath tub.
Fit the versatile faucet connectors to the bottom of both faucets using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, triggering the water to pass through the wall surface between the bath and also the tiling, leading to problems with moisture as well as feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealant can fracture fairly very early if you do not consider this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily readily available on the market. It is recommended to fit the floor tiles using water-resistant or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that blog posting about Installing A Bathtub while looking around the search engines. Enjoyed reading our write up? Please share it. Let another person locate it. Thank you for taking the time to read it.
Click For More Info Report this page